EPS消防應急電源該如何選擇？選型原則是什么？

EPS emergency power supply, how to choose? Selection What are the principles?

一、直流電源柜廠家負載容量選型原則:

因電動機的啟動沖擊，與其配用的集中應急電源容量按以下容量選配。

1、電動機變頻啟動時，應急電源容量可按電動機容量1.2倍選項配。

2、電動機軟啟動時，應急電源容量應不小于電動機容量的2.5倍。

3、電動機Y-△啟動時，應急電源應不小于電動機容量的3倍。

4、電動機直接啟動時,應急電源容量應不小于電動機容量的5倍。

5、混合負載中,大電機的容量若小于總負載容量的1/7.

A load capacity of the principle of selection:

Due to the impact of motor starting, its equipped with a centralized emergency power capacity in the following capacity matching.

1, the motor frequency starts, emergency power supply capacity can be 1.2 times the option with the motor capacity.

2, motor soft start, the emergency power supply capacity should be not less than 2.5 times the motor capacity.

3, the motor Y-△ start, the emergency power supply should not be less than three times the motor capacity.

4, motor direct start-up, emergency power supply capacity should be not less than five times the capacity of the motor.

5, the mixed load, the maximum capacity of the motor is smaller than if the total load capacity of 1/7.

二、選型容量計算方法:

1、柏克YJ系列或YJS系列用于帶應急燈具負載時：

（1）當負載為電子鎮流器日光燈，EPS容量計算方法：EPS容量=電子鎮流器日光燈功率和×1.1倍。

（2）當負載為電感鎮流器日光燈，EPS容量計算方法：EPS容量=電感鎮流器日光燈功率和×1.5倍。

（3）當負載為金屬鹵化物燈或金屬鈉燈，EPS容量計算方法：EPS容量=金屬鹵化物燈或金屬鈉燈功率和×1.6倍。

Second, the selection of capacity calculation method:

1, Burke YJ series or YJS series used with emergency lighting load:

(1) When the load is electronic ballast fluorescent, EPS capacity calculation method: EPS capacity = electronic ballast fluorescent lamp power and × 1.1-fold.

(2) When the load is inductive ballast fluorescent, EPS capacity calculation method: EPS capacity = inductive ballast fluorescent lamp power and × 1.5-fold.

(3) When the load is a metal halide lamp or a metal sodium, EPS capacity calculation method: EPS capacity = sodium metal or a metal halide lamp power and × 1.6 times.

2、當YJS系列用于帶混合負載時,EPS容量的計算方法:

（1）當EPS帶多臺電動機且都同時啟動時,則EPS的容量應遵循如下原則：

EPS容量=變頻啟動電動機功率之和+軟啟動電動機功率之和×2.5+星三角啟動機功率之和×3+直接啟動電動機之和×5倍

2, when the YJS series is used with mixed loads, EPS capacity calculation method:

(1) When the EPS with multiple motors and are simultaneously activated, then the capacity of the EPS should follow the following principles:

EPS capacity = frequency start the motor power and + soft start motor power of × 2.5 + star delta starter motor and the power of the motor is started directly × 3 + and × 5 times the

（2）當EPS帶多臺電動機且都分別單臺啟動時(不是同時啟動),則EPS的容量應遵循如下原則：

EPS容量=各個電動機功率之和,但必須滿足以下條件：

※ 上述電動機中直接啟動的大的單臺電動機功率是EPS容量的1/7.

※ 星三角啟動的大的單臺電動機功率是EPS容量的1/4.

※ 軟啟動的大的單臺電動機功率是EPS容量的1/3.

※ 變頻啟動的大的單臺電動功率不大于EPS的容量.

※ 如果不滿足上述條件,則應按上述條件中的大數調整EPS的容量,電動機啟動時的順序?yàn)橹苯訂?dòng)在先,其次是星三角的啟動,有軟啟動的再啟動,后是變頻啟動的再啟動.

(2) When more than one motor and belt EPS were all single boot (not simultaneously start), then the capacity of the EPS should follow the following principles:

EPS capacity = sum of all motor power, but must meet the following conditions:

※ The motor started directly largest single motor power is the EPS capacity of 1/7.

※ star delta starter largest single motor power is the EPS capacity of 1/4.

Soft start ※ largest single motor power is the EPS capacity of 1/3.

※ inverter startup largest single electric power less than EPS capacity.

※ If not the above conditions shall be the maximum number of the above conditions the capacity to adjust the EPS, the motor startup sequence is started directly first, followed by the star-delta start-up, a soft start re-start, and finally the frequency conversion re-start.

（3）當YJS系列EPS帶混合負載時EPS應遵循如下原則：

EPS容量=所有負載總功率之和,但必須中以下六條件,若不滿足,再按照其中大的容量確定EPS容量.

※ 負載中直接同時啟動的電動機功率之和是EPS容量的1/7

※ 負載中星三角同時啟動電動機功率之和是EPS容量的1/4

※ 負載中軟啟動同時啟動的電動機功率之和是EPS容量的1/3

※ 負載中變頻啟動同時啟動電動機功率之和不大于EPS的容量.

※ 同時啟動的電動機當量功率之和不大于EPS的容量.

電動機功率容量=直接啟動的電動機總功率x5+星三角同時啟動的電動機總功率x3+軟啟動同時啟動的電動機總功率x2.5+變頻啟動且同時啟動的電動機總功率

若電動機前后啟動時間相差大于1分鐘均不視為同時啟動。

※ 同時啟動的所有負載(含非電動機負載)的當量功率之和不大于EPS的容量。

同時啟動的所有負載的功率之和=同時啟動的非電動機總功率×功率因數+電動機當量總功率。

(3) When the YJS series EPS EPS with mixed loads should follow the following principles:

EPS capacity = total power of all loads, but it must in the following six conditions, if not met, then the capacity determined in accordance with one of the largest EPS capacity.

※ load directly activated simultaneously and that the EPS motor power capacity of 1/7

※ star delta load and start the motor power and is EPS capacity of 1/4

※ load soft start motor power of simultaneously started and is EPS capacity of 1/3

※ load and start motor power inverter startup and not greater than the capacity of the EPS.

※ started simultaneously equivalent power of the motor is not greater than the capacity of EPS.

Motor power capacity = direct start of motor power x5 + star delta start simultaneously x3 + motor power soft-start and start the motor power x2.5 + inverter motor starts and the total power simultaneously started

If the motor before start time difference than 1 minute are not regarded as the same time.

※ started simultaneously all loads (including non-motor loads) of equivalent power is not greater than the capacity of EPS.

Started simultaneously in all the power load and simultaneously start = total power × non-motor motor power factor + Equivalent total power.